Heat Pump Troubleshooting and Operation Questions

Modified on Tue, 17 Nov at 11:36 AM

Heat Pump Troubleshooting and Operation Questions

This article compiles agent-provided troubleshooting guidance for common heat pump questions covering display behavior and Follow Me, unknown symbols, electrical power/fuse checks, R‑454B pressure testing, EC51 error handling, controller compatibility, day-to-day operation tips, and indoor ice buildup.

Temperature display and Follow Me

  • The displayed temperature can be higher because the indoor unit measures air higher on the wall where warm air rises. Some units intentionally heat above the set point to warm the room evenly.
  • Enable Follow Me on the remote to use the remote’s temperature for more accurate control.
  • When Follow Me is ON, the unit displays the actual room temperature measured by the remote (not the setpoint). This is normal operation.

Unknown display: two parallel bars on Senville Aura

  • Two parallel bars do not correspond to any listed error code for Senville Aura and may indicate a display or control board issue.
  • Try restarting the unit with the remote to see if it responds.
  • If the issue persists, submit a support ticket with the complete model number and a photo via help.senville.com/support/tickets/new, and have a qualified HVAC technician handle any electrical intervention.

Outdoor power present at L1–L2 but not at terminals 1–2

  • If 240V is present between L1–L2 on the outdoor unit but not between terminals 1–2, blown inline fuses behind terminals 1–2 may be the cause.
  • Check the inline fuses (5mm × 20mm, 15A ceramic) located behind terminals 1–2 as the next step in troubleshooting.

R‑454B pressure testing (SENDC‑36HF)

  • Design pressures: 340 PSI on the low side and 550 PSI on the high side.
  • Pressure‑test each side to its respective design pressure.
  • If the high and low sides cannot be isolated, test the entire system to the low‑side design pressure (340 PSI).
  • Hold the test for at least 1 hour with no gauge‑pressure drop.
  • Only a licensed HVAC technician should perform refrigerant work.

EC51 error

  • EC51 indicates an outdoor control‑board/EEPROM error.
  • Power off the unit for two minutes and restore power. If the error returns, the outdoor PCB likely needs replacement by a licensed HVAC technician.
  • On some models, the entire outdoor electric control box may need replacement, not just the PCB; advise the technician to check this.
  • For warranty, provide purchase source and approximate date; proof of purchase is required, but support can often trace orders using the provided email and purchase details. Submit a warranty claim with available information and photos.

Controller compatibility (central systems)

  • Senville central systems require specific wired controllers (e.g., WRD‑RMT23 or WRD‑RMT25 for WiFi models).
  • Regular household thermostats like Google Nest are not supported on Senville mini‑splits.

Operation guidance

  • Set the heat pump to a comfortable temperature in HEAT mode and leave it there; the system will regulate itself.
  • Avoid setting the temperature much higher than desired.
  • If the unit runs continuously without reaching the set temperature, have a technician check the unit.
  • In mild weather, use AUTO mode so the unit can switch between heating and cooling as needed.
  • On multi‑zone systems, all indoor units must be set to the same mode.

Indoor unit ice buildup

  • Ice buildup on the indoor unit is abnormal and likely due to airflow or refrigerant issues.
  • Turn off the unit and let the ice fully melt before restarting.
  • Check and clean the air filter and ensure the indoor coil is not clogged.
  • Filter access and cleaning:
    • Turn off and disconnect power.
    • Open the top air intake/front panel at the “PULL” area.
    • Lift out the filter for inspection and cleaning.

Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons
CAPTCHA verification is required.

Feedback sent

We appreciate your effort and will try to fix the article