Senville AURA Series Error Code Reference Guide

Modified on Mon, 7 Apr at 10:32 AM

About This Guide

This article provides a complete list of error codes that may appear on Senville mini split indoor units. These codes help identify problems with sensors, communication, refrigerant, or other electrical components. Use the information below to troubleshoot or report issues.

Normal System Messages (Not Errors)

Code	Description	Solution
dF	Defrost	No action required — normal cycle
CL	Filter cleaning reminder / Active clean	Clean filters (displays 15 seconds after power-on)
F (some models)	Filter replacement reminder	Replace filters if applicable
FP	Heating mode in room temp under 8°C	No action required — automatic heating safeguard
FC	Forced cooling	Check if cooling was manually forced (e.g., by remote or setup)
AP	Wi-Fi AP mode	System is in Wi-Fi pairing mode — proceed via Alexa app
CP	Remote control switched off	Restart unit using remote or power cycle

Indoor Unit Error Codes

Code	Issue	Solution
EH 00	Indoor EEPROM malfunction	Replace indoor main PCB (TS01-IDU)
EH 0A	Indoor EEPROM parameter error	Reprogram or replace indoor PCB (TS01-IDU)
EL 01	Indoor & outdoor communication error	Check wiring and connectors; replace PCB if needed (TS02-S-INV)
EH 02	Zero-crossing signal detection error	Replace indoor main board (TS03)
EH 03	Indoor fan speed out of control	Check fan motor and control board (TS04-S-IDU)
EH 60	Room temperature sensor (T1) error	Replace T1 sensor (TS05-IDU)
EH 61	Pipe temperature sensor (T2) error	Replace T2 sensor (TS05-IDU)
EH 0	Display board and control board communication error	Check or replace one or both boards (TS07)
FH CC	Refrigerant sensor error	Replace sensor module (TS05-N10)
EH C1	Refrigerant leak detected	Check for refrigerant leaks and sensor (TS06-N10)
EH C2	Sensor out of range and leak detected	Replace sensor and inspect refrigerant line (TS06-N10)
EH C3	Sensor out of range	Replace refrigerant sensor (TS05-N10)
EC C1	Other indoor unit leak (multi-zone)	Leak inspection and sensor replacement (TS06-N10)

Outdoor Unit Error Codes

Code	Issue	Solution
EC 51	Outdoor EEPROM parameter error	Replace or reprogram outdoor board (TS01-ODU)
EC 52	Coil temp. sensor (T3) error	Replace T3 sensor (TS05-ODU)
EC 53	Ambient temp. sensor (T4) error	Replace T4 sensor (TS05-ODU)
EC 54	Compressor discharge temp. sensor (TP) error	Replace TP sensor (TS05-ODU)
EC 56	Indoor coil outlet temp. sensor (T2B) error (Multi-zone)	Replace T2B sensor (TS05-ODU)
EC 07	Outdoor fan speed out of control	Inspect fan motor and drive circuit (TS04-ODU)
EL 0C	System lacks refrigerant	Recharge system and inspect for leaks (TS06-INV)

Protection and System Errors

Code	Issue	Solution
PC 00	IPM module protection	Check cooling, IPM board (TS09-S)
PC 01	Voltage protection	Inspect input voltage (TS10-S)
PC 02	Compressor/IPM over-temperature	Inspect cooling, refrigerant flow (TS11-S-INV)
PC 04	Inverter compressor drive error	Replace or test drive module (TS12-S)
PC 03	Pressure protection (low/high)	Verify pressure sensors and refrigerant levels (TS26-INV)
PC 0L	Low ambient temp protection	No action needed unless malfunctioning (LP)
----	Multi-zone indoor units mode conflict	Ensure all units are set to the same mode (TS14)

Other Notes

If the display shows a **garbled or undefined code**, ensure it’s not just showing a temperature.
Use the remote control to test the unit:
- If it does not respond, the indoor PCB may need replacement.
- If it does respond, the issue may lie with the display board.

Need More Help?

Still having trouble? Submit a support ticket and include the error code, model number, and what steps you’ve already tried. Our technical team is ready to assist you.